Broadband & Digital subscriber line

Broadband in telecommunications is a term that refers to a signaling method that includes or handles a relatively wide range of frequencies, which may be divided into channels or frequency bins. Broadband is always a relative term, understood according to its context. The wider the bandwidth, the greater the information-carrying capacity. In radio, for example, a very narrow-band signal will carry Morse code; a broader band will carry speech; a still broader band is required to carry music without losing the high audio frequencies required for realistic sound reproduction. A television antenna described as "normal" may be capable of receiving a certain range of channels; one described as "broadband" will receive more channels. In data communications a modem will transmit a bandwidth of 64 kilobits per seconds (kbit/s) over a telephone line; over the same telephone line a bandwidth of several megabits per second can be handled by ADSL, which is described as broadband (relative to a modem over a telephone line, although much less than can be achieved over a fibre optic circuit, for example).[citation needed]
Broadband in data communications can refer to Broadband Networks or Broadband Internet and may have the same meaning as above, so that data transmission over a fiber optic cable would be referred to as broadband as compared to a telephone modem operating at 600 bits per second.[citation needed]
However, broadband in data communications is frequently used in a more technical sense to refer to data transmission where multiple pieces of data are sent simultaneously to increase the effective rate of transmission, regardless of actual data rate. In network engineering this term is used for methods where two or more signals share a medium.[citation needed]
The various forms of Digital Subscriber Line (DSL) services are broadband in the sense that digital information is sent over a high-bandwidth channel above the baseband voice channel on a single pair of wires.[citation needed]
A baseband transmission sends one type of signal using a medium's full bandwidth, as in 100BASE-T Ethernet. Ethernet, however, is the common interface to broadband modems such as DSL data links, and has a high data rate itself, so is sometimes referred to as broadband. Ethernet provisioned over cable modem is a common alternative to DSL.
Digital subscriber line
DSL or xDSL, is a family of technologies that provide digital data transmission over the wires of a local telephone network. DSL originally stood for digital subscriber loop, although in recent years, many[attribution needed] have adopted digital subscriber line as a more marketing-friendly term for the most popular version of consumer-ready DSL, ADSL. DSL uses high frequency; regular telephone uses low frequency.
Typically, the download speed of consumer DSL services ranges from 512 kilobits per second (kbit/s) to 24,000 kbit/s, depending on DSL technology, line conditions and service level implemented. Typically, upload speed is lower than download speed for Asymmetric Digital Subscriber Line (ADSL) and equal to download speed for Symmetric Digital Subscriber Line (SDSL).
Voice and data
Some variants of DSL connections, like ADSL and very high speed DSL (VDSL), typically work by dividing the frequencies used in a single phone line into two primary 'bands'. The ISP data is carried over the high frequency band (25 kHz and above) whereas the voice is carried over the lower frequency band (4 kHz and below). (See the ADSL article on how the high frequency band is sub-divided). The user typically installs a DSL filter on each phone. This filters out the high frequencies from the phone line, so that the phone only sends or receives the lower frequencies (the human voice). The DSL modem and the normal telephone equipment can be used simultaneously on the line without interference from each other.
History and science
Digital subscriber line technology was originally implemented as part of the ISDN specification, which is later reused as IDSL. Higher speed DSL connections like HDSL and SDSL have been developed to extend the range of DS1 services on copper lines. Consumer oriented ADSL is designed to operate also on a BRI ISDN line, which itself is a form of DSL, as well as on an analog phone line.
DSL, like many other forms of communication, stems directly from Claude Shannon's seminal 1948 scientific paper: A Mathematical Theory of Communication. Employees at Bellcore (now Telcordia Technologies) developed ADSL in 1988 by placing wideband digital signals above the existing baseband analog voice signal carried between telephone company central offices and customers on conventional twisted pair cabling.
U.S. telephone companies promote DSL to compete with cable modems. DSL service was first provided over a dedicated "dry loop", but when the FCC required the incumbent local exchange carriers ILECs to lease their lines to competing providers such as Earthlink, shared-line DSL became common. Also known as DSL over Unbundled Network Element , this allows a single pair to carry data (via a digital subscriber line access multiplexer [DSLAM]) and analog voice (via a circuit switched telephone switch) at the same time. Inline low-pass filter/splitters keep the high frequency DSL signals out of the user's telephones. Although DSL avoids the voice frequency band, the nonlinear elements in the phone would otherwise generate audible intermodulation products and impair the operation of the data modem.
Older ADSL standards can deliver 8 Mbit/s to the customer over about 2 km (1.25 miles) of unshielded twisted pair copper wire. The latest standard, ADSL2+, can deliver up to 24 Mbit/s, depending on the distance from the DSLAM. Distances greater than 2 km (1.25 miles) significantly reduce the bandwidth usable on the wires, thus reducing the data rate. By using an ADSL loop extender, these distances can be increased substantially.
In 2007, Dr. John Papandriopoulos, a University of Melbourne engineering researcher, patented algorithms that can potentially boost DSL line speeds to a maximum of 250 Mbit/s.
Operation
The local loop of the public switched telephone network (PSTN) was initially designed to carry POTS voice communication and signaling, since the concept of data communications as we know it today did not exist. For reasons of economy, the phone system nominally passes audio between 300 and 3,400 Hz, which is regarded as the range required for human speech to be clearly intelligible. This is known as voiceband or commercial bandwidth.
At the local telephone exchange (United Kingdom) or central office (United States) the speech is generally digitized into a 64 kbit/s data stream in the form of an 8 bit signal using a sampling rate of 8,000 Hz, therefore, according to the Nyquist theorem, any signal above 4,000 Hz is not passed by the phone network (and has to be blocked by a filter to prevent aliasing effects).
The laws of physics, specifically the Shannon limit, cap the speed of data transmission. For a long time, it was believed that a conventional phone line couldn't be pushed beyond the low speed limits (typically under 9600 bit/s). In the 1950s, 4 MHz television signals were often carried between studios on ordinary twisted pair telephone cable, suggesting that the Shannon Limit would allow transmitting many megabits per second. However, these cables had other impairments besides Gaussian noise, preventing such rates from becoming practical in the field. In the 1980s techniques were developed for broadband communications that allowed the limit to be greatly extended.
The local loop connecting the telephone exchange to most subscribers is capable of carrying frequencies well beyond the 3.4 kHz upper limit of POTS. Depending on the length and quality of the loop, the upper limit can be tens of megahertz. DSL takes advantage of this unused bandwidth of the local loop by creating 4312.5 Hz wide channels starting between 10 and 100 kHz, depending on how the system is configured. Allocation of channels continues at higher and higher frequencies (up to 1.1 MHz for ADSL) until new channels are deemed unusable. Each channel is evaluated for usability in much the same way an analog modem would on a POTS connection. More usable channels equates to more available bandwidth, which is why distance and line quality are a factor (the higher frequencies used by DSL travel only short distances). The pool of usable channels is then split into two different frequency bands for upstream and downstream traffic, based on a preconfigured ratio. This segregation reduces interference. Once the channel groups have been established, the individual channels are bonded into a pair of virtual circuits, one in each direction. Like analog modems, DSL transceivers constantly monitor the quality of each channel and will add or remove them from service depending on whether they are usable.
One of Lechlider's greatest contributions to DSL was his insight that an asymmetric arrangement offered more than double the bandwidth capacity of synchronous DSL. This allowed Internet Service Providers to offer efficient service to consumers, who benefitted greatly from the ability to download large amounts of data but rarely needed to upload comparable amounts. ADSL supports two modes of transport: fast channel and interleaved channel. Fast channel is preferred for streaming multimedia, where an occasional dropped bit is acceptable, but lags are less so. Interleaved channel works better for file transfers, where transmission errors are impermissible, even though resending packets may increase latency.
Because DSL operates at above the 3.4 kHz voice limit, it cannot be passed through a load coil. Load coils are, in essence, filters that block out any non-voice frequency. They are commonly set at regular intervals in lines placed only for POTS service. A DSL signal cannot pass through a properly installed and working load coil, nor can voice service be maintained past a certain distance without such coils. Some areas that are within range for DSL service are disqualified from eligibility because of load coil placement. Because of this phone companies are endeavoring to remove load coils on copper loops that can operate without them, and conditioning lines not to need them through the use of fiber to the neighborhood or node FTTN.
The commercial success of DSL and similar technologies largely reflects the advances made in electronics, that, over the past few decades, have been getting faster and cheaper even while digging trenches in the ground for new cables (copper or fiber optic) remains expensive. Several factors contributed to the popularization of DSL technology:
Until the late 1990s, the cost of digital signal processors for DSL was prohibitive. All types of DSL employ highly complex digital signal processing algorithms to overcome the inherent limitations of the existing twisted pair wires. Due to the advancements of VLSI technology, the cost of the equipment associated with a DSL deployment (a DSLAM at one end and a DSL "modem" at the other end) lowered significantly.
A DSL line can be deployed over existing cable. Such deployment, even including equipment, is much cheaper than installing a new, high-bandwidth fiber-optic cable over the same route and distance. This is true both for ADSL and SDSL variations.
In the case of ADSL, competition in Internet access caused subscription fees to drop significantly over the years, thus making ADSL more economical when compared to dial up access. Telephone companies were pressured into moving to ADSL largely due to competition from cable companies, which use DOCSIS cable modem technology to achieve similar speeds. Demand for high bandwidth applications, such as video and file sharing, also contributed to popularize ADSL technology.
Most residential and small-office DSL implementations reserve low frequencies for POTS service, so that with suitable filters and/or splitters the existing voice service continues to operate independent of the DSL service. Thus POTS-based communications, including fax machines and analog modems, can share the wires with DSL. Only one DSL "modem" can use the subscriber line at a time. The standard way to let multiple computers share a DSL connection is to use a router that establishes a connection between the DSL modem and a local Ethernet, Powerline, or Wi-Fi network on the customer's premises.
Once upstream and downstream channels are established, they are used to connect the subscriber to a service such as an Internet service provider.
Dry-loop DSL or "naked DSL," which does not require the subscriber to have traditional land-line telephone service, started making a comeback in the US in 2004 when Qwest started offering it, closely followed by Speakeasy. As a result of AT&T's merger with SBC, to consumers.
Even without the regulatory mandate, however, many ILECs offer naked DSL to consumers. The number of telephone landlines in the US has dropped from 188 million in 2000 to 172 million in 2005, while the number of cellular subscribers has grown to 195 million. This lack of demand for landline service has resulted in the expansion of naked DSL availability.